CARB stands for California Air Resources Board, also known as Air Resources Board (ARB). It is a department of the California Environmental Protection Agency. It was established in 1967 with the purpose of maintaining and improving air quality, and researching causes and solutions of air pollution. CARB's mandates, such as CARB 2 compliant MDF, are strict and usually are considered the standard across the United States.
What is CARB Phase 2 Compliant?
CARB Phase 1 and Phase 2 are a part of California's Composite Wood Products Regulation (CWP Regulation), which took effect in 2009 with Phase 1. The regulation has to do with reducing formaldehyde emissions from composite wood products, hardwood plywood, particleboard and medium density fiberboard (MDF). In the 2009 rollout of the CARB's Airborne Toxic Control Measure (ATCM), formaldehyde emissions were capped at .08 parts per million (ppm). CARB Phase 2 went into effect in 2010 and has much lower formaldehyde emissions than the previous phase; set at .05 ppm. A main reason why the CARB ATCM is the strictest air quality measure is because it CAPS emissions levels. Other air quality standards are averages.
Pewter Grey Shaker
Ships in 5-15 business days
Accident Protection Warranty For Your Entire Bathroom! Learn More!
The Pewter Grey Shaker features a classic shaker style door and a beautiful grey finish. It pairs perfectly with the Aspen White Shaker to combine white and grey in the same room. With soft close drawers and doors, and an all plywood box construction, you can rest easy that you're getting high quality cabinets that will stand the test of time!
Shipping Time: |
Ships in 5-15 business days |
Style: | Shaker |
Face Frame: | 3/4 Solid Wood |
Door Frame: | HDF(HDF is used to avoid cracking/warping) |
Door Center: | MDF (MDF is used to avoid cracking/warping) |
Door Frame Width: | 3" |
Center Panel Beveled Edge: | No |
Sides: | 1/2" A-Grade plywood with wood veneer |
Top & Bottom (Wall): | 1/2" A-Grade plywood with wood veneer |
Bottom (Base): | 3/8" A-Grade plywood with wood veneer |
Back Panel: | 1/2" Picture Frame Recess Style |
Shelves: | 3/4 " A-Grade plywood with wood veneer |
Base Cabinet Shelf Depth: | 1/2 |
Drawer Box: | Solid Wood 17mm (close to 3/4") sides, Drawer bottom 1/2" plywood, Drawer length 21". Dovetail construction, Natural finish. |
Drawer Glides: | Undermount, full extension with soft closing feature |
Base Corner Supports: | Wood corner brackets with wood I-beam construction |
Overlay: | Full with butt doors |
Hinges: | Concealed 6-way adjustable with Soft Closing Feature |
Cabinet Interior: | Matches door finish |
Center Stile: |
No center stile on cabinetry 24"W to 36"W |
Assembly Method: | Steel Clip |
Finish: | Waterborne UV Finish |
Toe Kick: |
1/2" Plywood (sides of the toe kicks will be unfinished)
|
Installation Rail: | 1/2" Plywood |
Wall Cabinet Bottoms Finished (Exterior): | Yes |
CARB Compliant: | Yes |
Door Hinges: | Hinged To The Right By Default. For Wall Cabinets The Face Frame Can Be Flipped. For Base Cabinets Unhinge The Door, Flip It, Screw Holes On The Opposite Side To Re-Hinge, And Then Fill The Original Holes (Touch Up Kit Can Be Purchased For This) |
Toe Kicks Included w/Base Cabinets: | Yes |
Sides Panels Finished: | Yes |
Installation/Designer Note: |
The full-overlay door style leaves roughly a 1/4" clearance on the edge. If installed directly against a wall or deeper cabinet and a cabinet door opening of at least 90 degrees is desired, scribe molding should be installed between the cabinet and the wall (or deeper cabinet). If not, the door may not be able to open a full 90 degrees. For a full opening, a space of at least 1/4-1/2" is necessary, a larger space may be needed depending on the decorative hardware used on the cabinets. The cabinet depth measurement listed is the depth from the front of the face frame to the back of the cabinet, and does not include the cabinet door depth. Cabinet specs are subject to change without notice. *Cabinet measurements are typically converted from metric to inches and manufacturers will commonly round up to the nearest 1/4 inch. This can cause a measurement to be off by a fraction of an inch (less than 1/4") which is within normal industry standards* Schematic images and renderings are generic and may not represent exact construction details for each collection. The exact specificationsforthis collection can be found in theconstruction detailslisted above. |
Assembly instructions for all cabinets - schematic drawings
-
View All
-
Vanities with No Drawers
-
Vanities with Drawers
-
Drawer Base Cabinets - 24" Deep
-
Drawer Base Vanities
-
Desk Drawer and Mirrors
-
Sink Base Cabinets - 24" Deep
Please note that all cabinet images are to show the final product, but assembly will be required.
-
View All
-
30" High Single Door Wall Cabinets
-
30" High Double Door Wall Cabinets
-
36" High Single Door Wall Cabinets
-
36" High Double Door Wall Cabinets
-
42" High Single Door Wall Cabinets
-
42" High Double Door Wall Cabinets
-
12" Deep Small Wall Cabinets
-
24" Deep Small Wall Cabinets
-
30", 36", and 42" High Wall Diagonal Corner Cabinets
-
Wall End Shelf Cabinets
-
Wall Angle Cabinets
-
Wall Specialty Cabinets
-
Hoods
-
Wall Cabinets With Drawers
-
Blind Wall Cabinets
-
Wall Cabinet Hanging Kit
Please note that all cabinet images are to show the final product, but assembly will be required.
-
View All
-
Linen/Pantry Cabinets
Please note that all cabinet images are to show the final product, but assembly will be required.