CARB stands for California Air Resources Board, also known as Air Resources Board (ARB). It is a department of the California Environmental Protection Agency. It was established in 1967 with the purpose of maintaining and improving air quality, and researching causes and solutions of air pollution. CARB's mandates, such as CARB 2 compliant MDF, are strict and usually are considered the standard across the United States.
What is CARB Phase 2 Compliant?
CARB Phase 1 and Phase 2 are a part of California's Composite Wood Products Regulation (CWP Regulation), which took effect in 2009 with Phase 1. The regulation has to do with reducing formaldehyde emissions from composite wood products, hardwood plywood, particleboard and medium density fiberboard (MDF). In the 2009 rollout of the CARB's Airborne Toxic Control Measure (ATCM), formaldehyde emissions were capped at .08 parts per million (ppm). CARB Phase 2 went into effect in 2010 and has much lower formaldehyde emissions than the previous phase; set at .05 ppm. A main reason why the CARB ATCM is the strictest air quality measure is because it CAPS emissions levels. Other air quality standards are averages.
Vail White Shaker
Ships in 5-15 business days
Accident Protection Warranty For Your Entire Bathroom! Learn More!
The Vail White Shaker collection features a classic shaker style with a stunning white paint that will brighten up any sized bathroom! You won't have to worry about compromising on the amenities with the Vail White Shaker collection where soft close hinges and drawer glides come standard! Its clean lines will match any decor and with a plywood box construction, you can rest easy that it will stand the test of time.
This finish is available in both Ready to Assemble and Pre-Assembled
Shipping Time: |
Ships in 5-15 business days |
Matching Collections: | |
Style: | Shaker |
Face Frame: | 3/4" Solid wood |
Door Frame: | 3/4" Solid wood |
Door Center: | HDF (Reversed raised door panel) |
Door Frame Width: | 2.375" |
Center Panel Beveled Edge: | No |
Sides: | 1/2" A-Grade plywood with wood veneer |
Top & Bottom (Wall): | 1/2" A-Grade plywood with wood veneer |
Bottom (Base): | 3/8" A-Grade plywood with wood veneer |
Back Panel: | 1/2" Full back |
Shelves: | 3/4 " A-Grade plywood with wood veneer |
Base Cabinet Shelf Depth: | 1/2 |
Drawer Box: | Solid Wood 17mm (close to 3/4") sides, Drawer bottom 3/8" plywood, Drawer length 21". Dovetail construction, Natural finish. |
Drawer Glides: | Undermount, full extension with soft closing feature |
Base Corner Supports: | Metal corner brackets |
Overlay: | Full with butt doors |
Hinges: | Concealed 6-way adjustable with Soft Closing Feature |
Cabinet Interior: | Natural Finish |
Center Stile: |
No center stile on cabinetry 24"W to 36"W |
Assembly Method: | L-bracket |
Finish: | Polyurethane finish |
Toe Kick: | 1/2" Plywood (sides of the toe kicks will be unfinished) |
Installation Rail: | None (there is a full back) |
Wall Cabinet Bottoms Finished (Exterior): | Yes |
CARB Compliant: | Yes |
Door Hinges: | Hinged To The Right By Default. For Wall Cabinets The Face Frame Can Be Flipped. For Base Cabinets Unhinge The Door, Flip It, Screw Holes On The Opposite Side To Re-Hinge, And Then Fill The Original Holes (Touch Up Kit Can Be Purchased For This) |
Toe Kicks Included w/Base Cabinets: | Yes |
Sides Panels Finished: | Yes |
Installation/Designer Note: |
The full-overlay door style leaves roughly a 1/4" clearance on the edge. If installed directly against a wall or deeper cabinet and a cabinet door opening of at least 90 degrees is desired, scribe molding should be installed between the cabinet and the wall (or deeper cabinet). If not, the door may not be able to open a full 90 degrees. For a full opening, a space of at least 1/4-1/2" is necessary, a larger space may be needed depending on the decorative hardware used on the cabinets. The cabinet depth measurement listed is the depth from the front of the face frame to the back of the cabinet, and does not include the cabinet door depth. Cabinet specs are subject to change without notice. *Cabinet measurements are typically converted from metric to inches and manufacturers will commonly round up to the nearest 1/4 inch. This can cause a measurement to be off by a fraction of an inch (less than 1/4") which is within normal industry standards* Schematic images are generic and may not represent exact construction details for each collection. The exact specificationsforthis collection can be found in theconstruction detailslisted above. |
Assembly instructions for all cabinets - schematic drawings
-
View All
-
Sink Base Cabinets - 24" Deep
-
Drawer Base Cabinets - 24" Deep
Please note that all cabinet images are to show the final product, but assembly will be required.
-
View All
-
30" High Single Door Wall Cabinets
-
30" High Double Door Wall Cabinets
-
36" High Single Door Wall Cabinets
-
36" High Double Door Wall Cabinets
-
42" High Single Door Wall Cabinets
-
42" High Double Door Wall Cabinets
-
Wall Cabinets With Drawers
-
Blind Wall Cabinets
-
Wall Cabinet Hanging Kits
Please note that all cabinet images are to show the final product, but assembly will be required.
-
View All
-
Linen/Pantry Cabinets
Please note that all cabinet images are to show the final product, but assembly will be required.
-
View All
-
Valances
-
Moldings
-
Wall and Base Fillers
-
Fluted Decorative Wall and Base Fillers
-
Panels
-
Decorative Doors
-
Decorative/Accent Pieces
-
Lift Up Hinge and Hinge Restrictors
-
Touch Up
-
Recommended Decorative Hardware
-
Base Trash Cabinet Accessories