CARB stands for California Air Resources Board, also known as Air Resources Board (ARB). It is a department of the California Environmental Protection Agency. It was established in 1967 with the purpose of maintaining and improving air quality, and researching causes and solutions of air pollution. CARB's mandates, such as CARB 2 compliant MDF, are strict and usually are considered the standard across the United States.
What is CARB Phase 2 Compliant?
CARB Phase 1 and Phase 2 are a part of California's Composite Wood Products Regulation (CWP Regulation), which took effect in 2009 with Phase 1. The regulation has to do with reducing formaldehyde emissions from composite wood products, hardwood plywood, particleboard and medium density fiberboard (MDF). In the 2009 rollout of the CARB's Airborne Toxic Control Measure (ATCM), formaldehyde emissions were capped at .08 parts per million (ppm). CARB Phase 2 went into effect in 2010 and has much lower formaldehyde emissions than the previous phase; set at .05 ppm. A main reason why the CARB ATCM is the strictest air quality measure is because it CAPS emissions levels. Other air quality standards are averages.
Portland White
Product Overview
Ships in 5-15 business days
Accident Protection Warranty For Your Entire Laundry Room! Learn More!
The Portland White cabinet collection offers a fresh, crisp, and clean look to any laundry Room. The bright white finish will surely lighten the laundry Room space and add a modern touch to your home. These cabinets are full overlay doors and come with beautiful dovetail drawers and soft closing drawer features.
Specifications
This finish is available in both Ready to Assemble and Pre-Assembled
| Shipping Time: |
Ships in 5-15 business days |
| Matching Collections: |
   |
| Style: | Slim Shaker |
| Face Frame: | 3/4 Solid Wood |
| Door Frame: | MDF (MDF is used to avoid cracking/warping) |
| Door Center: | MDF (MDF is used to avoid cracking/warping) |
| Center Panel Beveled Edge: | No |
| Sides: | 1/2" A-Grade plywood with wood veneer |
| Top & Bottom (Wall): | 1/2" A-Grade plywood with wood veneer |
| Bottom (Base): | 3/8" A-Grade plywood with wood veneer |
| Back Panel: | 1/2" full back |
| Shelves: | 3/4 " A-Grade plywood with wood veneer |
| Base Cabinet Shelf Depth: | 1/2 |
| Drawer Box: | Solid Wood 17mm (close to 3/4") sides, Drawer bottom 3/8" plywood, Drawer length 21". Dovetail construction, Natural finish. |
| Drawer Glides: | Undermount, full extension with soft closing feature |
| Base Corner Supports: | Wood corner brackets with wood I-beam construction |
| Overlay: | Full with butt doors |
| Hinges: | Concealed 6-way adjustable with Soft Closing Feature |
| Cabinet Interior: | Matches door finish |
| Center Stile: |
No center stile on cabinetry 24"W to 36"W |
| Assembly Method: | Steel Clip |
| Finish: | Waterborne UV Finish |
| Toe Kick: | 1/2" Plywood (sides of the toe kicks will be unfinished) |
| Installation Rail: | 1/2" Plywood |
| Wall Cabinet Bottoms Finished (Exterior): | Yes |
| CARB Compliant: | Yes |
| Door Hinges: | Hinged To The Right By Default. For Wall Cabinets The Face Frame Can Be Flipped. For Base Cabinets Unhinge The Door, Flip It, Screw Holes On The Opposite Side To Re-Hinge, And Then Fill The Original Holes (Touch Up Kit Can Be Purchased For This) |
| Toe Kicks Included w/Base Cabinets: | Yes |
| Sides Panels Finished: | Yes |
| Installation/Designer Note: |
The full-overlay door style leaves roughly a 1/4" clearance on the edge. If installed directly against a wall or deeper cabinet and a cabinet door opening of at least 90 degrees is desired, scribe molding should be installed between the cabinet and the wall (or deeper cabinet). If not, the door may not be able to open a full 90 degrees. For a full opening, a space of at least 1/4-1/2" is necessary, a larger space may be needed depending on the decorative hardware used on the cabinets. The cabinet depth measurement listed is the depth from the front of the face frame to the back of the cabinet, and does not include the cabinet door depth. Cabinet specs are subject to change without notice. *Cabinet measurements are typically converted from metric to inches and manufacturers will commonly round up to the nearest 1/4 inch. This can cause a measurement to be off by a fraction of an inch (less than 1/4") which is within normal industry standards* Schematic images and renderings are generic and may not represent exact construction details for each collection. The exact specifications for this collection can be found in the construction details listed above. |
Assembly
Assembly instructions for all cabinets - schematic drawings
Wall Cabinets
Base Cabinets
Pantry Cabinets
Cabinet Accessories
Storage Accessories
-
View All
-
Sample Door
-
30" High Single Door Wall Cabinets
-
30" High Double Door Wall Cabinets
-
36" High Single Door Wall Cabinets
-
36" High Double Door Wall Cabinets
-
42" High Single Door Wall Cabinets
-
42" High Double Door Wall Cabinets
-
12" Deep Small Wall Cabinets
-
24" Deep Small Wall Cabinets
-
Diagonal Corner Wall Cabinets
-
Wall End Shelf Cabinets
-
Wall Angle Cabinets
-
Wall Specialty Cabinets
-
Hoods
-
Wall Cabinets With Drawers
-
Wall Cabinet Hanging Kits
Please note that all cabinet images are to show the final product, but assembly will be required.
-
View All
-
Single Door Base Cabinets
-
Double Door Base Cabinets
-
Drawer Base Cabinets
-
Corner Base Cabinets
-
Blind Corner Base Cabinets
-
Sink Base Cabinets
-
Base Pull Out Spice Cabinets
-
Base Angle Cabinets
-
Microwave Base Cabinet
-
Base Transitional Cabinet
-
Base Trash Cabinet Accessories
Please note that all cabinet images are to show the final product, but assembly will be required.